Home Improvement

Thoughts & Stuff I Like When We Redid Our House

Raise Panel

Expanding Options For Solar Panel Buyers

For lots of years, the only kinds of solar panels commercially offered have been crystalline solar panels put in a rectangular casing and positioned on a roof. This is why nearly everyone, as soon as they think of solar power for their house, imagine this as their single option. Below are a few new advancements in solar power and mounting options you may have never heard of before.

Thin Film Solar Panels - Man Is This Skinny!

Think of the solar panel you have in a solar calculator. That is a thin film solar panel. Thin film solar panels are used to a great extent in satellites. Thin film technology is now being expanded into residential and commercial use and was named one of the best inventions of 2008 by TIME magazine.

Thin film solar panels are bendable, unlike polysilicon cells found in conventional crystalline solar panels. These thin film solar panels are being hailed as second generation solar power technology.

Thin film solar panels are more resistant to hail, rocks, and so on. If part of a crystalline solar panel is damaged, the entire solar panel will stop functioning while a thin film solar panel will go on functioning.

Thin film panels can also be flexible and modified to a lot of surfaces. They can be applied in places conventional crystalline solar panels cannot be mounted on top of. I have even seen a thin film panel sewed on a coat that powered a MP3 player.

The downside to thin film panels is that they do not take in as much energy because they are so thin. These panels are not nearly as efficient as traditional photovoltaic panels but they cost less. Thin film solar panels are printed onto the rolled backing, eliminating many of the high energy and chemical intensive processes that are normal in conventional PV manufacturing.

Thin film solar panels are low wattage and have need of more space than traditional solar panels and they are more prone to degradation. In order to counteract several of these competitive disadvantages they have versus traditional solar panels, manufacturers offer better warranties for thin film panels.

The largest thin film solar photovoltaic (PV) project in the United States is the Blythe plant located 190 miles east of Los Angeles, California. The 21-megawatt solar power plant uses thin film solar cells made out of cadmium telluride. At full power, the plant will make enough electricity to power an estimated 16,500 homes.

Now let us examine traditional solar panels and some of the mounting options that are offered that you might not know exist.

Mounting Options For Conventional Solar Panels - It's All About the Mount

Solar panel mounts are available in three main types: pole mounts, roof-ground mounts, and flush mounts. With these mounts, you can fix your solar panel onto an RV, on top of or against the side of a pole, on your roof, or even install them as a free-standing unit.

Pole Mounts - No That Is Not What Santa Claus Uses For His Sleigh

Pole mounts, specially top-of-pole, have been popular for a long time. Top-of-pole mounts are essentially a steel or aluminum rack and rail structure bolted or welded to a large casing that sets on top of a pole with set-bolts to keep it stationary. Side-of-pole mounts are regularly used when you must mount to the side of a telephone pole or communications tower. Tracking mounts are similar to top-of-pole mounts, but they also have a system of automatically aiming the mount to stay on the sun.

Top of pole mounts (including sun trackers) are one of the simplest mounts to install. They really only need a single steel pole set in the ground (usually in concrete), and the mount slips onto the top of the pole. Most ordinary sizes use a 2-inch to 8-inch pole, usually around 11 to 13 feet in length. They can go higher if you want to get the panel up higher to escape shading from nearby vegetation.

Those Roof-Ground Mounts

Roof-ground systems can be mounted onto a roof or ground without a lot of variation in setup. They are usually built from stainless steel in a grid-like system of supports. Roof-mounted panels for smaller systems are the easiest to mount, using little flush-mount brackets that raise the panels to the best angle for solar collection.

Ground mounts, as the name implies, are solar panel mounts that are installed on the ground (as opposed to a pole mount or roof mount). They have supporting, variable legs that allow you to optimize their vertical orientation for solar exposure. Ground mounting systems usually entail plenty of steel supports, concrete foundations, and galvanized footings, that can be challenging, when you are trying to keep your system low cost. Ground mounted systems require structural strength to prevent load bearing failure.

Even though module mounting systems are available for ground and roof installation, roof mount installation is the most popular and cost effective approach. The roof mounted panels are attached to a mounting system typically consisting of an aluminum or steel support structure which attaches the panels to the roof.

Flush Mounts

Flush Mounts are inexpensive and straightforward to install - these are ideal for single panel installations and smaller solar arrays. Flush mounts are put onto a level surface such as a rooftop, the top of a boat, or the top of a recreational vehicle and are not used for ground installations. These mounts function to separate the solar panel from the mounting surface and permit airflow to go under and cool the solar panel for efficient operation. Flush Mounts are usually used with small solar arrays on roof tops and RVs, because the structural design of a flush mount cannot hold up large solar panels.

About the Author

Find out what the big energy companies don't want you to know. Learn everything there is to know about solar power and wind power technology at
where can I buy solar panels

When Anthem Wellpoint raises Premiums on the sick, is it a Death Panel?

The object is to get the really sick people off their rolls, but what happens to them? Do they just die?
Is this the private insurers version of the Death Panel?

It sure is. Private insurers want only healthy people. If someone gets sick, the sooner they die or drop the insurance the better.

Weaver Three Shaper System's Crown Panel Trimming